The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
The publisher is making a number of great annotation on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this post beneath.
Mounting a tub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is readily accessible, the task can move quickly; if you need to open up a wall to get rid of the old tub and also position the new tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will require an assistant to leave the old bathtub and set in the brand-new one. Make certain you have qualified yourself for the work and are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is far better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already gotten a brand-new tub as well as do not need to change the arrangement of your previous water system pipes.
Your tools and product checklist should consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is detach the water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather troublesome as a result of the restricted gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to going on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the faucet in place with the maker supplied backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Using the two wooden boards under its feet, position the bathtub in the required position. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To set up taps, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water system and inspect all joints and also new pipework for leakages and tighten them if required. Fill up the tub and also inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, deal with the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the tub needs to wait up until the bathtub has been utilized at least when as this will resolve it right into its last setting.
Preparing for the Installment
First of all, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final placement.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall surface in between the bath and also the tiling, resulting in problems with dampness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to permit the movement experienced when the tub remains in use. The sealant can fracture relatively very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently offered on the market. It is suggested to fit the tiles utilizing water-resistant or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about A Step-by-Step Guide to Installing a Bathtub? Make feedback down the page. We'd be pleased to listen to your reactions about this article. We hope that you come back again before long. So long as you appreciated our page plz make sure you remember to pass it around. I praise you for your time. Kindly come visit our site back soon.
Expert care? Call. Report this page